From an engineer’s perspective, wheel bearing design and selection can be a balancing act between durability, cost and fuel economy. A large bearing might be great to offset potholes and heavy loads. But, there is only so much room in the hub and knuckle. Also, the larger bearing might have increased rolling resistance due to a larger sealing surface. On the other hand, if the bearing is too small in diameter, it might not be able to withstand heavy loads, plus there might not be enough room for the axle. Two technologies are being used on new vehicles and in aftermarket replacement hub units that are allowing engineers to put better bearings in smaller packages. Related Articles - Livestream Next Week: Lowering Springs and Lift Kits - LED Lighting – What Are the OES Doing and What Can You Do? - Hyundai Brake Caliper Fluid Inspection
Better designs are needed to accommodate large diameter wheels, which apply a heavier bending movement on the hub’s flange. Also, many of today’s vehicles have twice the power compared to new models of just a decade ago. This extra power can cause stress on the splines and stub axle. Car Wheel Bearing Assembly
Most driven wheel bearing hubs have a male-splined axle that slides through a matching female-splined hole in the hub. The whole thing is held together with an axle nut. This design has been used for more 60 years.
Splines have their limits when it comes to the size of the hub, amount of power and load that can be transmitted to the wheels. Increasing the number of splines and the diameter of the stub axle can make the hub unit too large for the knuckle and increase rolling resistance.
The latest hub design moves the splines from inside the bearing races to the back of the hub. Axial- or face-spline hubs have what looks like gear teeth on the backside of the hub assembly unit and can be found on BMW X5 and X3 SUVs.
Matching axial gear teeth are formed on the end of the CV joint, and the whole unit is held in place with a long bolt.
The axial-spline arrangement allows higher torque transmission than the traditional splined CV method, primarily because the gear teeth operate on a much larger pitch circle. This design allows for a smaller diameter hole in the center that can improve the stiffness of the bearing and its durability. It also can reduce brake pedal pulsation and travel.
These units come preassembled and preloaded from the manufacturer. The preload is set by cold rolling the inner race under many tons of pressure.
Asymmetrical wheel bearing hubs use different bearing row diameters to improve load capacity and overall stiffness. The hub’s outboard row has a larger diameter than the inner row and more rollers or balls. Hybrid asymmetrical designs use both rollers and ball bearings in the two rows.
The design increases the bearing load capacity and the unit is stiffer than a conventional hub of the same size. This stiffness prevents the brake rotor from flexing and tilting while the vehicle is cornering, and reduces brake caliper piston knockback that can cause a long brake pedal.
Both axial and asymmetrical bearings need to be installed using either the correct service or bearing manufacturer installation information. Hub units are typically preassembled and are simply bolted to the suspension. These are “maintenance-free” and non-serviceable units that are pre-set, pre-greased and pre-sealed.
Some applications use a torque-to-yield bolt that stretches and keeps constant tension. These bolts may attach the hub unit to the knuckle. In the case of axial splined hubs, a torque-to-yield bolt holds the hub to the axle. These bolts can’t be used twice.
While it may appear to be easier to use an impact wrench to tighten the axle nut or bolt, it is not recommended. The recommendation is to use a torque wrench.
Impact wrenches can damage the axle nut, threads and components. These can also create a false sense of security when adjusting a nut or bolt, which may be under- or over-torqued, leaving a hub assembly susceptible to failure.
Cincinnati, OH non-profit brings cars and people together to remove transportation barriers, build community.
Reflashing and reprogramming is a necessary service for repairing vehicles.
If you fail to inspect an item on the schedule, you could miss out on maintenance opportunities.
Joe Keene carefully walks though the steps for calibrating a Honda front radar camera. Sponsored by Hunter Engineering.
Car Front Wheel Bearing Technical Resources for diagnosing and servicing undercar components